Custom flashing
Eave, rake, ridge, valley and wall trim in the same finish so the roof sheds water at every edge.
Metal Roofing
Metal Roof Installation Bergenfield, NJ
Metal roof installation in Bergenfield starts with choosing the panel system, the metal and the finish, then building the roof from underlayment to ridge cap, with high-temperature underlayment, matched trim and closures at every edge. Call (551) 374-2021 to reach a local roofer.
Before anything else, a metal roof starts with picking how the panels attach. Ribbed and corrugated panels fasten through the face with washered screws, which keeps installation simple but leaves fasteners exposed to the weather. Standing seam panels hide their clips under raised seams, so nothing pierces the flat of the panel and the metal can expand and contract freely.
Next comes the metal itself and the paint on it. Galvanized and Galvalume coated steel cover most homes, aluminum resists corrosion near salt air, and copper and zinc are long-lived specialty metals. PVDF finishes resist fading better than SMP finishes, and gauge, where a lower number means thicker metal, affects dent resistance.
What goes under the metal is easy to overlook and important to get right. A solid deck covered with high-temperature underlayment is the usual base, plus ice and water shield at eaves and valleys where needed. Open purlin framing works on outbuildings, while homes are better served by a full deck.
Metal Roof Installation is often paired with standing seam metal roof and metal roof replacement, depending on the cause.
Looking for Bergenfield metal roof installation? Call (551) 374-2021 to reach a nearby roofing contractor.
Call nowThe process
Installing a metal roof
A metal roof is measured, ordered and installed as a matched system.
Pick the panel
After choosing standing seam, ribbed panels or metal shingles, the roof is measured to order panels and trim. Accurate measurements mean fewer end laps.
Prepare the deck
Rotted decking is replaced and the surface made flat before any metal goes on. An even deck reduces waviness in the panels.
High-heat underlayment
A heat-rated underlayment goes down over the whole roof, plus an ice barrier in leak-prone areas. A slip sheet may be used to let the metal slide over the underlayment.
Set the trim
Eave trim and drip edge go on first, along with valley flashing, so panels can lap over them. Rake trim and ridge cap come later and overlap the panels.
Install the panels
Each panel is aligned, lapped and fastened so the roof stays straight from end to end. Cut edges are kept clean of metal shavings that rust.
Finish the details
The ridge, walls, chimneys and pipes are flashed, and closures seal the gaps under the trim. Where snow is common, snow guards protect gutters and people below.
What is included
What a metal roof installation includes
Underlayment
The deck is covered in underlayment made for metal so it does not stick or break down.
Snow guards
Pipe boots made for metal and snow guards over entries finish the job to protect people and gutters below.
Panel selection
A panel system matched to the roof pitch chosen to fit the house and budget.
Ridge ventilation
Vented ridge closures let the attic breathe and block insects and birds.
Related service
Metal Roofing Contractor Bergenfield, NJ
Metal roofing is its own trade, with seaming tools, brakes for bending trim and an understanding of thermal movement. Good questions cover the panel systems they install, the underlayment they use and how they detail valleys and walls.
For Bergenfield homeowners, the right metal roofing contractor will show how each system handles your roof shape. Ask to see a few local roofs they have done, and look at how straight the panels run and how the trim meets the walls.
Related service
Stone Coated Steel Roof Bergenfield, NJ
A stone coated steel roof uses steel panels coated with stone granules set in an acrylic base, shaped to look like shake, tile or shingles. It is lighter than tile, resists wind and hail well, and the granules soften the sound of rain.
Most stone coated steel goes on a batten system that adds ventilation beneath the panels. It suits Bergenfield homes where heavy tile would need framing upgrades.
Related service
Metal Shingle Roof Bergenfield, NJ
Metal shingles are individual interlocking panels shaped like traditional roofing units. Hidden fasteners and small units make them a good fit for roofs with dormers and valleys.
In Bergenfield, metal shingles appeal to homeowners who want metal performance with a traditional look. The roofer follows the specific instructions for that shingle profile.
Local help
Metal Roof Installation Near Me
Around Bergenfield, metal roofing shows up on new homes, reroofs of older houses, garages and farm buildings. Across Bergenfield and nearby communities including New Milford, Dumont, River Edge and Cresskill, metal roofs suit older farmhouses and new builds alike, so it pays to compare systems before choosing.
Searching for metal roof installation near me from Bergenfield or New Milford, Dumont, River Edge and Cresskill? Call (551) 374-2021 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Bergenfield
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Bergenfield is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Bergenfield
Roofers in Bergenfield know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Common questions about metal roof installation
Should I choose standing seam or exposed fastener metal roofing?
The two systems attach the metal in different ways. Exposed fastener panels are screwed through the face, which is simpler and quicker but leaves washers that will need replacing, while standing seam uses hidden clips that let the panels move. Many homeowners choose standing seam for houses and exposed fastener for barns and shops.
What gauge of metal roofing should I use?
Metal thickness is listed as gauge, with smaller numbers being thicker. Thicker metal resists dents and oil canning better. The right gauge depends on the panel and the weather it faces.
What is the lifespan of a metal roof?
Metal roofs often last two or three times as long as asphalt shingles. Concealed fastener systems usually outlast exposed fastener roofs, which need periodic screw replacement. Coastal exposure and dissimilar metals can shorten it.
Is a metal roof louder in the rain?
On a house with decking and attic insulation, a metal roof is usually only slightly louder than shingles. Metal over open framing, like a barn, is the noisy version. Stone coated steel and metal shingles are among the quietest options.
Does a metal roof attract lightning?
A metal roof does not make a strike more likely. Strikes depend on height, terrain and nearby objects, and a metal roof is no more likely to be hit than any other roof. If a strike happens, metal will not catch fire like some roofing can.
More questions? Call (551) 374-2021
Related services
Standing Seam Metal Roof
Standing seam metal roofing installed, repaired and detailed for thermal movement, built to let the metal move without leaking.
Learn moreMetal Roof Replacement
Tearing off failed metal panels, repairing the framing and putting on a new metal roof, so the new roof starts on a sound base.
Learn moreRoof Installation
Installing a new roof layer by layer, from drip edge and underlayment to flashing, vents and the finished roofing, whether it is asphalt shingles, metal or another material.
Learn moreCommercial Metal Roofing
Commercial metal roofing from structural standing seam to exposed fastener panels, plus retrofits over old roofs, planned around the building and its operations.
Learn more
Looking for something else?
See all roofing servicesTalk to a Bergenfield roofer about metal roof installation
Call (551) 374-2021 to talk to a roofer serving Bergenfield, NJ.