Roof vents
An exhaust system sized for the attic for a drier attic all year.
A roofer in Bergenfield can install a new roof in the proper sequence: drip edge, ice and water shield, underlayment, starter strip, flashing, vents and then the roofing itself, whether the roof is going on a stripped deck or as a permitted overlay. Dial (551) 374-2021 to talk with a local roofer about installation.
A quality roofing material can still fail early if it is installed carelessly. Shingles nailed too high above the nail line can blow off in the first strong wind, a missing kickout flashing can rot a wall where the roof meets the siding, and a valley done wrong can funnel water under the roofing. Those are details you cannot see from the yard, which is why the installer matters so much.
Choosing the material comes first. Most homes get dimensional asphalt shingles, but metal panels, stone coated steel, tile and slate are all options, and each has its own installation rules. The slope of the roof limits the options, because shingles need a minimum pitch and nearly flat sections need a membrane roof.
A Bergenfield roofer will ask a handful of questions up front. Mention whether the old roof is coming off or this is new framing, what material you have in mind and any spots that have leaked before.
If the problem goes deeper than it first looked, a Bergenfield roofer may also recommend roof replacement or shingle roof installation.
Looking for Bergenfield roof installation? Call (551) 374-2021 to talk to a local roofer.
Call nowA roof goes on from the bottom of the system to the top.
Installation starts on a sound, dry deck, so damaged sheathing is cut out and replaced first. On an overlay, the old shingles must lie flat, and any badly curled ones are cut back or replaced.
Drip edge goes on at the eaves, ice and water shield is rolled out along the eaves and in the valleys, and drip edge is then added along the rakes over the underlayment. This is the part of the roof most likely to see ice and backed-up water.
Underlayment rolls go on from the eaves up, with laps that shed water down the roof. Synthetic is lighter, tears less and stays put better than felt if it rains mid-job.
Each sidewall gets step flashing course by course, chimneys get step and counter flashing and vent pipes get new boots. Reused or caulk-only flashing is one of the most common installation shortcuts.
Starter shingles seal the first course, and each shingle is nailed through the marked nail line, not above it. Correct nailing is what lets the roof stand up to wind.
A ridge vent is cut in along the peak and covered with ridge cap shingles, matched to the intake at the soffits. Mixing different exhaust vents on one roof can short-circuit the airflow, so one system is chosen.
An exhaust system sized for the attic for a drier attic all year.
New flashing at every wall, chimney and vent pipe seals the places where the roof meets something else.
Ice and water shield at the eaves and valleys, with underlayment over the rest of the deck guards the deck if ice dams form.
The finished roofing, installed to the maker's nailing and fastening pattern in straight, even courses.
Drip edge at the eaves and rakes guides water into the gutters and protects the fascia.
New roof installation covers three common jobs: replacing a roof after tear-off, roofing a new home and roofing an addition. Additions take extra care, because the new roof has to tie into the old one with matching shingles, woven or flashed valleys and step flashing where the new roof meets an existing wall. Ask whether the new section will match the existing roofing or whether the whole roof should be redone.
The installation should follow the roofing maker's printed instructions, which spell out nailing, underlayment, slope limits and ventilation. When talking with a Bergenfield roofer, ask about the nailing pattern, the underlayment and how intake and exhaust will balance. Those answers reveal a lot about how the roof will hold up.
An overlay skips the tear-off and lays new shingles over the current roof. Most codes allow no more than two layers, which means an overlay is ruled out if there are already two, or if the deck is soft or the old shingles are buckled. It saves the labor of a tear-off and keeps the house closed during the job.
An overlay comes with downsides worth weighing. The deck stays hidden, ice barrier cannot be applied directly to the wood and any wear in the old roof shows through the new one. If an overlay is on the table, ask the roofer to confirm the layer count, replace the drip edge and flashing and explain what happens at the next replacement, when both layers must come off.
In Bergenfield, new roofs go on everything from decades-old homes to recent builds. Older homes in Bergenfield and nearby towns like New Milford, Dumont, River Edge and Cresskill often need extra deck work and better ventilation, while newer homes are more likely to need flashing tied into new siding, and a careful installation is what lets a new roof ride out years of weather.
For roof installation in Bergenfield, NJ or nearby towns like New Milford, Dumont, River Edge and Cresskill, call (551) 374-2021 to reach a roofer who covers your street.
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Bergenfield is busiest after a hard winter and before the next one.
Small roof problems caught early usually stay small repairs.
Local roofers see the same roofs and storm damage across Bergenfield and nearby towns.
Ask the roofer about the cause, the options and the estimate before work starts.
More questions? Call (551) 374-2021
Replacing an aging roof with new underlayment, flashing, vents and roofing, built to current code from the decking out.
Learn moreNew shingle roofs built layer by layer on a sound deck, so the roof sheds water and handles wind from day one.
Learn moreMetal roof installation built around the right panel, finish and trim for the house, for homes, garages and outbuildings.
Learn moreRoofing for new homes, additions, garages and other new framing, from dry-in to the finished ridge, so the house is protected before interior work starts.
Learn moreLooking for something else?
See all roofing servicesCall (551) 374-2021 to talk to a roofer serving Bergenfield, NJ.